MAHLE / CLEVITE : CB1657P |
Connecting Rod Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
SEALED POWER : 4775A |
Connecting Rod Bearing |
- Housing Bore Max (MM): 54.9960 ;
- Housing Bore Max (in): 2.1652 ;
- Housing Bore Min (MM): 54.9860 ;
- Housing Bore Min (in): 2.1648 ;
- Oil Clearance Max (MM): 0.0430 ;
- Oil Clearance Max (in): 0.0017 ;
- Oil Clearance Min (MM): 0.0150 ;
- Oil Clearance Min (in): 0.0006 ;
- Overall Length Max (MM): 16.5000 ;
- Overall Length Max (in): 0.6490 ;
- Standard Shaft Max (MM): 51.9990 ;
- Standard Shaft Max (in): 2.0472 ;
- Standard Shaft Min (MM): 51.9840 ;
- Standard Shaft Min (in): 2.0466 ;
- Wall Thickness Max (IN): 0.0589 ;
- Wall thickness Max (MM): 1.4980 ;
|
ITM ENGINE COMPONENTS : 4B9633 |
Connecting Rod Bearing |
|
ENGINETECH : BB4125 |
Connecting Rod Bearing |
- Housing Bore: 2.1648-2.1652 in ;
- Number of Bearings: 4 ;
- Oil Clearance: 0.0006-0.0017 in ;
- Shaft Diameter: 2.0466-2.0472 in ;
- Wall Thickness: 0.0586-0.0591 in ;
- Width: 0.648 IN ;
|
ITM ENGINE COMPONENTS : 4B9654 |
Connecting Rod Bearing |
|
MAHLE / CLEVITE : CB1657HX |
Connecting Rod Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : CB1657HXC |
Connecting Rod Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : CB1657HC |
Connecting Rod Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : CB1657H |
Connecting Rod Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : BB2055 |
Connecting Rod Bearing |
|
ENGINETECH : BB1067 |
Connecting Rod Bearing |
- Housing Bore: 2.1648-2.1652 in ;
- Number of Bearings: 4 ;
- Oil Clearance: 0.0008-0.0018 in ;
- Shaft Diameter: 2.0466-2.0472 in ;
- Wall Thickness: 0.0587-0.0592 in ;
- Width: 0.651 IN ;
|
ENGINETECH : BB4280 |
Connecting Rod Bearing |
- Housing Bore: 2.0079-2.0085 in ;
- Number of Bearings: 4 ;
- Oil Clearance: 0.0006-0.0017 in ;
- Shaft Diameter: 1.8875-1.8890 in ;
- Wall Thickness: 0.0585-0.0590 in ;
- Width: 0.615 IN ;
|
MAHLE / CLEVITE : CB1657HK |
Connecting Rod Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|