t a  e 
参考号 零件 参数
ENGINETECH : BB1538 Connecting Rod Bearing
  • Housing Bore: 2.2800-2.2800 in ; 
  • Number of Bearings: 6 ; 
  • Oil Clearance: 0.0008-0.0017 in ; 
  • Shaft Diameter: 2.1644-2.1654 in ; 
  • Wall Thickness: 0.0588-0.0593 in ; 
  • Width: 0.567 in ; 
ITM ENGINE COMPONENTS : 6B1503 Connecting Rod Bearing
MAHLE / CLEVITE : CB1897A6 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1861P Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1861HX Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1861H Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
ENGINETECH : BB1013 Connecting Rod Bearing
  • Housing Bore: 2.0079-2.0087 in ; 
  • Number of Bearings: 4 ; 
  • Oil Clearance: 0.0008-0.0020 in ; 
  • Shaft Diameter: 1.8896-1.8898 in ; 
  • Wall Thickness: 0.0584-0.0589 in ; 
  • Width: 0.614 IN ; 
ITM ENGINE COMPONENTS : 4B1203 Connecting Rod Bearing
MAHLE / CLEVITE : CB1861P4 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
ITM ENGINE COMPONENTS : 4B1711 Connecting Rod Bearing
MAHLE / CLEVITE : CB1862A4 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
ENGINETECH : BB1065 Connecting Rod Bearing
  • Housing Bore: 1.6929-1.6938 in ; 
  • Number of Bearings: 4 ; 
  • Oil Clearance: 0.0008-0.0015 in ; 
  • Shaft Diameter: 1.5739-1.5748 in ; 
  • Wall Thickness: 0.0592-0.0597 in ; 
  • Width: 0.531 in ; 
MAHLE / CLEVITE : CB1862A Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1976A4 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
SEALED POWER : 65005A Connecting Rod Bearing
  • Housing Bore Max (MM): 58.0000 ; 
  • Housing Bore Max (in): 2.2834 ; 
  • Oil Clearance Max (MM): 14.5000 ; 
  • Oil Clearance Max (in): 0.0019 ; 
  • Wall Thickness Max (IN): 0.0594 ; 
  • Wall thickness Max (MM): 1.5100 ; 
ENGINETECH : BB1021 Connecting Rod Bearing
  • Number of Bearings: 4 ; 
  • Oil Clearance: 0.0009-0.0017 in ; 
  • Shaft Diameter: 1.7707-1.7716 in ; 
MAHLE / CLEVITE : CB1830AL Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
ENGINETECH : BB1033 Connecting Rod Bearing
  • Housing Bore: 2.2434-2.2441 in ; 
  • Number of Bearings: 6 ; 
  • Oil Clearance: 0.0005-0.0028 in ; 
  • Shaft Diameter: 2.1229-2.1235 in ; 
  • Wall Thickness: 0.0592-0.0597 in ; 
  • Width: 0.673 IN ; 
ITM ENGINE COMPONENTS : 6B3007 Connecting Rod Bearing
MAHLE / CLEVITE : CB1860P Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
ITM ENGINE COMPONENTS : 4B9642 Connecting Rod Bearing
ENGINETECH : BB1536 Connecting Rod Bearing
  • Housing Bore: 1.9000-1.9000 in ; 
  • Number of Bearings: 4 ; 
  • Oil Clearance: 0.0008-0.0019 in ; 
  • Shaft Diameter: 1.7707-1.7717 in ; 
  • Wall Thickness: 0.0587-0.0592 in ; 
  • Width: 0.606 IN ; 
ENGINETECH : BB1025 Connecting Rod Bearing
  • Number of Bearings: 6 ; 
  • Oil Clearance: 0 ; 
  • Shaft Diameter: 2.0857-2.0866 in ; 
  • Width: 0.573 IN ; 
ITM ENGINE COMPONENTS : 6B1504 Connecting Rod Bearing
MAHLE / CLEVITE : CB1780P Connecting Rod Bearing
  • 1.8888: 1.8898 ; 
  • Min Shaft: Max Shaft ; 
MAHLE / CLEVITE : CB1780H Connecting Rod Bearing
  • 1.8888: 1.8898 ; 
  • Min Shaft: Max Shaft ; 
MAHLE / CLEVITE : CB1780HX Connecting Rod Bearing
  • 1.8888: 1.8898 ; 
  • Min Shaft: Max Shaft ; 
ENGINETECH : BB1520 Connecting Rod Bearing
  • Housing Bore: 2.0079-2.0088 in ; 
  • Number of Bearings: 4 ; 
  • Oil Clearance: 0.0008-0.0034 in ; 
  • Shaft Diameter: 1.8888-1.8898 in ; 
  • Wall Thickness: 0.0589-0.0594 in ; 
  • Width: 0.768 in ; 
ITM ENGINE COMPONENTS : 4B9544 Connecting Rod Bearing
MAHLE / CLEVITE : CB1780P4 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1859P Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
ITM ENGINE COMPONENTS : 4B1204 Connecting Rod Bearing
ENGINETECH : BB1501 Connecting Rod Bearing
  • Housing Bore: 1.8898-1.8907 in ; 
  • Number of Bearings: 4 ; 
  • Oil Clearance: 0.0007-0.0017 in ; 
  • Shaft Diameter: 1.7707-1.7717 in ; 
  • Wall Thickness: 0.0585-0.0590 in ; 
  • Width: 0.610 IN ; 
MAHLE / CLEVITE : CB1975A4 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
[1]
共
34
条记录，分
1
页显示
按品牌拼音首字母查找：

      尺寸/参数

      标注 名称 尺寸范围 单位
          

      标注实例

      联系客服

      客服电话：020-36390347